je.st
news
Tag: 181a
SP4T Broadband RF Switches consume 120 µA.
2014-09-23 14:33:13| Industrial Newsroom - All News for Today
Delivering alternative to GaAs technology, PE42542 and PE42543 are based on UltraCMOS® technology and offer bandwidth that maintains performance across 9 kHz to 18 GHz range. Respective values for PE42542 and PE42543 include linearity of 58 and 59 dBm IIP3 (118 and 113 dBm IIP2), switching time of 3 µsec and 500 nsec, and ESD ratings of 3.5/2.5 kV HBM, 150 V MM, and 500/250 V CDM on all pins. Settling time of 7 µsec (PE42542) eliminates gate lag, and PE42543 has 2 µsec settling time. This story is related to the following:Electrical Equipment and SystemsSearch for suppliers of: Multi-Throw Single Pole Switches |
Tags: broadband
switches
consume
181a
Magnetic Single-Chip Encoder consumes just 3 µA.
2014-09-09 14:30:51| Industrial Newsroom - All News for Today
Housed in 4 x 4 mm QFN16 package, Model iC-TW11 allows for 10-bit angle detection, suitable for battery-buffered applications. With sampling rate of 10 Hz, average current consumption of 3 µA is obtained, and in standby mode between measuring cycles, idle current cuts back to 100 nA. Model iC-TW11 supports sampling rates of 4 kHz with activated filter and automatic amplifier gain for 10-bit resolution at maximum accuracy. Four-wire SPI interface can be operated with up to 16 MHz clock frequency. This story is related to the following:Test and Measuring InstrumentsMagnetic Encoders | Integrated Circuits (IC)
Tags: magnetic
encoder
consumes
181a
FPGAs feature 50 µA static current consumption.
2013-10-29 13:29:35| Industrial Newsroom - All News for Today
Available in 30-ball, 2.09 x 2.54 mm WLCSP package and 64-ball, 3.5 x 3.5 mm VFBGA package, PolarPro® 3 Series is architected to meet power, space, and functionality requirements of next-generation mobile device OEMs. Reprogrammable devices feature 50 µA of standby current, up to 1,019 logic cells, 64 kb of user-programmable SRAM, and embedded FIFO controllers. This story is related to the following:Gate Arrays |
Tags: current
feature
static
consumption
Rail-to-Rail Single Op Amps draw as little as 0.6 µA.
2013-04-17 14:29:13| Industrial Newsroom - All News for Today
While TS1003 draws 0.6 µA and exhibits 4 kHz gain-bandwidth product (GBWP) and TS1005 draws 1.3 µA and exhibits 20 kHz GBWP, both are fully specified over -40 to +85°C range and come in SC70-5 packaging. These operational amplifiers (op amps), which exhibit typical input bias current of 2 pA, feature rail-to-rail input/output stages, are optimized for ultra-long-life battery-powered applications, and support single-supply operation from 0.8–5.5 V. This story is related to the following:Operational Amplifiers
Non-Contact Rotary Position Sensor consumes 300 µA at 3.3 V.
2013-02-13 14:34:05| Industrial Newsroom - All News for Today
Operating from 1.8–5.5 V supply, Contelec Vert-X 21 LP Series can be ordered as 3-wire angle sensor or programmable version with up to 2 switch outputs, custom measurement angle, start- and end-point settings, custom characteristic curve and/or sense of rotation. Products offer 0° to 360° measurement range, 12-bit resolution, repeatability to 0.1°, and max hysteresis of 0.2° Measuring less than 1 in. dia, IP65-rated sensors have life rating of 360+ million movements. This story is related to the following:Rotary Position Sensors
Tags: v
position
sensor
rotary
Sites : [1]